HondaVert preCAN – HondaVert

Information

Install

Usefull

Download

HondaVert preCAN daughter board for Honda Accord, Element, CR-V and Acura RSX ECU, which significantly expands capacity of it.
Datalog, RealTime Programming, Launch Control, Boost Control, Nitrous Control and more. Fully retains all vehicle systems. ABS, VSA, Gauges, Climate control and etc.

HondaVert preCAN compatible with the following cars

This solution is suitable for vehicles without ECU replacement

05-06 Acura RSX Facelift
03-07 Honda Accord USA (CM4-CM8)
03-06 Honda Element
02-06 Honda CR-V 2.4 (for SWAP ONLY)

This solution is suitable for vehicles (required OEM ECU replacement to prepared ECU)
*After replacing ECU, Cruise control system, ABS, VSA stay functional.

03-07 Honda Accord EuroR JDM
03-07 Honda Accord Manual Transmission (CL7-CL9)
03-07 Acura TSX Manual Transmission (CL7-CL9)

COOMING SOON! Honda Accord/Acura TSX Automatic Transmission Conversion KIT

03-07 Honda Accord Automatic Transmission (CL7-CL9)
03-07 Acura TSX Automatic Transmission (CL7-CL9)

HondaVert preCAN advantage

OEM Wideband O2 sensor
Traction Control for better stability (Addon module)
Bluetooth (Addon module)
Extra analog inputs
FlexFuel input for GM sensor
Drive by Wire and Cable Throttle Setups
Support CANBUS GAUGES (Honda Accord)
Automatic and Manual Transmission support

What sotware can I use?

KTuner
HV ECU Manager (under development)

All HondaVert preCAN devices compatible with KTuner 1.0.11.2.

Software downloaded from other sites not compatible with HondaVert preCAN devices.

HondaVert preCAN can be installed to this type of ECU’s

PND – Acura RSX 05-06 [CABLE THROTTLE]
RAD – Honda Accord USA 03-05 [CABLE THROTTLE, CANBUS GAUGES]
RAD – Honda Accord USA 06-07 [DBW, CANBUS GAUGES]
PZD – Honda Element 03-06 [CABLE THROTTLE]
PPA – Honda CR-V 03-05 [CABLE THROTTLE, CANBUS GAUGES]
PPA – Honda CR-V 06-07 [DBW, CANBUS GAUGES]

Other ECU’s that have an interface on the PCB (pins for soldering CN101 and CN4)

HondaVert preCAN board Installation

Be careful not to get soldering flux on connector CN101 and CN4 on the ECU board: when heated, the flux forms a film on the contacts and the ECU is not programmed. If there are ECU programming errors after installation, then you need to check the soldering and clean the contacts with a paper knife.

Solder connectors **CN101** and **CN4** from install kit to ECU

Make a hole in ECU case for USB Connector. Install preCAN Board with supplied screws from installation pack

KTuner 1.0.11.2 HondaVert Pack Installation Guide

We recommend to disable antivirus software and windows defender before installing. Software does not contain viruses, but makes changes to the system files, which may raise warning in your antivirus software or windows defender.

Run **«hvkt_setup_1.0.11.2.exe»**. Follow instructions of installation wizard.

Install **preCAN** drivers. Follow instructions of installation wizard.

Registering New Account or Login into Existing Account

Internet connection required to work with KTuner software

After first start **KTuner Assistant** guide you to install drivers. You do not need this drivers, just ignore it. Click **Next** and then **Finish**.

Registering a New Account

If you don’t have Hondavert Account in KTuner Software. Connect USB cable to **preCAN** device. In **Account Management** window enter your Email, Name and Password to create new account. Click **Register** button.
**Do not lose your account password – password recovery is a paid procedure!**

If you done everything correctly, you will see a window with a message about successful registration of your account. Click OK and then **CLOSE** in **Account Management** window.

Login Into Existing Account

If you already have Hondavert Account in KTuner Software. Connect USB cable to **preCAN** device. In **Account Management** window enter your Email, Name and Password and click **Update** button to synchronize your local data with Hondaver server.

If you done everything correctly, you will see a window with a message about successful update of your licenses. Click OK and then **CLOSE** in **Account Management** window.

Each preCAN device must be registered in your account and locked to ECU.

Registering preCAN in Account

After login, **KTuner** software will determine a new **preCAN** device that is not registered in your account and will offer to register it. Press **YES**.

If you done everything correctly, you will see a window with a message about successful registration. Click OK.

Lock preCAN device to ECU

Turn ignition ON. **KTuner** will detect a new ECU and offer you to Lock **preCAN** device to this ECU. Press **YES**.

If you done everything correctly, you will see a window with a message about successful Lock to ECU. Click OK.

Information About your Devices and ECU’s

preCAN LEDs meaning

There are HL1 RED, HL2 BLUE , HL3 GREEN, HL4 GREEN LEDs near the USB connector.

HL1	HL2	HL3	HL4	Meaning
On	Off	Off	Blinking Slowly	ECU NOT Powered or NO Communication with ECU
Blinking Slowly	Data Transfer	Off	Blinking Slowly	ECU Powered with Factory Codebase
Off	Off	Blinking Fast	Blinking Slowly	ECU Powered with KTuner Codebase.
Off	Data Transfer	Blinking Fast	Blinking Fast	Datalogging with PC via USB
Blinking Fast	Data Transfer	Blinking Fast	Blinking Slowly	PreCAN OnBoard Logging Active (PC Datalogging inactive)
On With Flickering	Data Transfer	Blinking Fast	Blinking Slowly	PreCAN OnBoard Logging Erasure (PC Datalogging inactive)
Off	Data Transfer	Blinking Fast	Blinking Slowly	Downloading Codebase form ECU
On	Data Transfer	Off	Blinking Slowly	Uploading Codebase to ECU

Mechanical and Electronic throttle bodies differences

preCAN compatible ECU’s are supports multiple types of throttle bodies

**Cable throttle**. Driven by cable. Throttle Position Sensor (TPS) and Idle Air Control Valve. (IACV) are mounted on the throttle body.

**Electronic Throttle**. Also known as Drive by Wire. Based on the signal from the. Accelerator Pedal Position Sensor (APP SENSOR).

For “swap” K engine with DBW into a chasis with a Cable, we need to buy two. modules from a Honda Accord or CR-V with DBW system:

**a) Accelerator Pedal Position Sensor module (APP SENSOR). Part Number 37971-RBB-003**

**b) DBW Control unit. Part number 37850-PPD-911**

False virus detections are possible. If you have problem with downloading – disable your Antivirus software and Windows Defender.

PASSWORD FOR ARCHIVES EXTRACTING: 1234

KTuner 1.0.11.2 [HV REPACK]

290.1 MB

Download